New Construction Electrical Inspection
Get your new construction wired right, inspected right, and approved the first time.
5 Highlights on New Construction Electrical Inspection
- Rough-in inspection ready: Kochs Electric schedules and prepares every rough-in inspection before drywall goes up, verifying that all conduit runs, wire pulls, junction boxes, and panel rough-ins meet NEC code requirements.
- Service entrance and meter base compliance: Our journeymen and master electricians install and inspect service entrances, meter bases, and main disconnects to satisfy utility company and local authority having jurisdiction (AHJ) standards.
- AFCI and GFCI protection verified: Every branch circuit gets tested for arc-fault and ground-fault protection, confirming that tamper-resistant receptacles and CFCI devices are correctly installed in required locations.
- Panel and load center inspection: We inspect load centers, subpanels, busbars, neutral bars, and ground bars for proper torque on lugs and terminals, correct wire sizing, and compliant labeling on every circuit breaker.
- Permit card and final sign-off: Kochs Electric manages the inspection card from permit pull through final inspection, coordinating directly with the inspector to get your certificate of occupancy without delays.
Why Choose Our New Construction Electrical Inspection
New construction electrical inspection is a multi-stage process. It demands precision at every phase, from rough-in through final inspection. Kochs Electric brings licensed master electricians and experienced journeymen to homes, businesses, and job sites of every size.
We wire, connect, and terminate to NEC standards on every project. Our foremen verify that all conduit, Romex, MC cable, and EMT installations pass before the inspector ever walks the site. We also handle repairs and upgrades when needed to prevent compliance issues from slowing your project down.
As a licensed contractor, Kochs Electric holds all required state electrical licenses and carries full liability insurance. We’ve built a track record of passing rough-in inspections, safety inspections, and final inspections on the first visit across residential and commercial new construction projects.
Our team uses calibrated torque wrenches, voltage testers, and multimeters on every inspection walkthrough. We don’t guess at wire sizing or circuit load calculations. We provide accurate power load documentation, measure, verify, and certify before we call for inspection.
Builders and general contractors trust Kochs Electric because we communicate clearly, show up on schedule, and deliver compliant work. We coordinate with inspectors, pull permits, and keep your project moving. Contact us any business day to learn how Kochs Electric can handle all your electrical needs from permit pull to final sign-off.
Signs You Need New Construction Electrical Inspection
1. Rough-in work is complete but hasn’t been verified: Your electrician has run conduit, pulled wire, and mounted junction boxes throughout the framing. Before drywall gets installed, a new construction electrical inspection confirms that all rough-in work is compliant. Concealed wiring that fails inspection after drywall means costly tear-out. Catching non-compliant work at the rough-in stage saves time and money.
2. Your panel and subpanel installations haven’t been checked: A load center with improperly torqued lugs, overcrowded wiring, undersized feeders, or missing surge protection on dedicated equipment circuits is a fire hazard. New construction electrical inspection covers the panel, subpanel, busbar, neutral bar, and ground bar before the system gets energized. An inspector verifies that every circuit breaker is correctly sized and labeled.
3. AFCI and GFCI devices aren’t confirmed compliant: NEC code requires arc-fault circuit interrupters on most branch circuits in new residential construction. Ground-fault protection is required in kitchens, bathrooms, near water sources, garages, and outdoor locations. If your electrician hasn’t verified AFCI and GFCI placement against current code, your final inspection will fail.
4. Service entrance and meter base work is complete: The service entrance, meter base, and main disconnect are the first points of inspection for the utility company and the AHJ. Exposed conductors, improper bonding, or a non-compliant grounding electrode system will stop your project cold. New construction electrical inspection catches these issues before the utility energizes the service.
5. You’re approaching final inspection without a pre-inspection walkthrough: A failed final inspection delays your certificate of occupancy. Kochs Electric conducts a thorough pre-inspection walkthrough, testing every outlet, receptacle, switch, and fixture. We verify that all trim-out work is finished, all devices are properly secured, and the inspection card is complete before the inspector arrives.
Our New Construction Electrical Inspection Process
Step 1: Permit pull and plan review Kochs Electric pulls the electrical permit and reviews the electrical plan and blueprints. We confirm that the planned circuit layout, panel sizing, and service entrance design comply with NEC code, city requirements, and local amendments.
Step 2: Rough-in inspection preparation Our journeymen walk the framing stage, verifying conduit runs, wire pulls, stapling, strapping, and junction box placement. We check that all boxes are accessible, correctly sized, and properly secured before we schedule the rough-in inspection.
Step 3: Rough-in inspection coordination We coordinate directly with the inspector, present the inspection card, and walk the site. Any items the inspector flags get corrected immediately. We re-schedule re-inspection without delay.
Step 4: Trim-out and device installation After drywall, our electricians install receptacles, outlets, switches, dimmers, lighting fixtures, and panels. We torque all lugs and terminals to spec, label every circuit breaker, and test each branch circuit with a voltage tester and multimeter.
Step 5: Final inspection and sign-off Kochs Electric schedules the final inspection and accompanies the inspector through the completed project. We verify that all AFCI, GFCI, and tamper-resistant devices pass, and we secure the final sign-off on the inspection card.
Brands We Use
Kochs Electric installs and inspects equipment from the most trusted names in the electrical industry. These brands meet NEC standards and pass inspection consistently.
- Square D
- Leviton
- Eaton
- Hubbell
- Southwire
- Klein Tools
- Fluke
- Ideal Industries
- Carlon
- Greenfield / AFC Cable
Every brand Kochs Electric installs is UL listed and code compliant. We don’t cut corners on materials.
Other Services
| New construction electrical inspection | New build electrical inspection | Rough-in inspection NEC compliance |
| Electrical inspection new construction | Residential new construction electrical | Panel inspection new construction |
| New construction electrical contractor | New home electrical inspection service | AFCI GFCI inspection new build |
| New construction wiring inspection | Commercial new construction electrical inspection | Service entrance inspection permit |
| Electrical permit inspection new construction | New construction electrical code inspection | Final electrical inspection certificate occupancy |
FAQs About New Construction Electrical Inspection
What is a new construction electrical inspection?
A new construction electrical inspection is a code compliance review conducted by a licensed inspector at defined stages of a new build project. It covers rough-in wiring, panel installation, service entrance work, and final trim-out to confirm that all electrical work meets NEC standards and local code requirements.
When does a new construction electrical inspection happen?
Inspections happen at two primary stages. The rough-in inspection occurs after wiring, conduit, and junction boxes are installed but before drywall covers the work. The final inspection happens after all devices, fixtures, panels, and service equipment are fully installed and the system is ready to energize.
Why does new construction need an electrical inspection?
New construction electrical inspection protects occupants from fire hazards, shock risks, and non-compliant wiring. Safety is the primary reason electrical inspections exist at every stage. It also protects the property owner legally. Without a passed inspection and a signed inspection card, a building can’t receive a certificate of occupancy.
How does Kochs Electric prepare for a new construction electrical inspection?
We pull permits, review blueprints, verify rough-in work against NEC code, torque all connections, test every circuit, and conduct a pre-inspection walkthrough before calling for inspection. Our goal is a first-time pass on every rough-in and final inspection.
Can a new construction electrical inspection fail?
Yes. Common reasons for failure include undersized wire, missing AFCI or GFCI protection, improperly torqued lugs, overcrowded panels, non-compliant grounding, and missing permits. Kochs Electric addresses all of these before the inspector arrives.
Does Kochs Electric handle the permit process?
Yes. We pull the electrical permit, manage the inspection card, and coordinate scheduling with the local AHJ from start to final sign-off.