Now Serving All of Indiana - Licensed electricians dispatched from Indianapolis.

Emergency calls welcome: (317) 680-7907

Commercial Property Electrical Inspection

Get your commercial property inspected, verified, and certified by qualified electricians who know what’s at stake.

State Licensed
Master Electricians
Permit & Inspection Handled
24-Hour Emergency Line
Workmanship Guaranteed

Licensed, Bonded & Insured

NEC Code Compliant

Same-Day Emergency Response

Permits Pulled & Inspections Managed

Workmanship Guarantee

Serving All of Indiana

5 Highlights on Commercial Property Electrical Inspection

Full panel and distribution board assessment

Kochs Electric inspects every breaker, busbar, and switchgear component for signs of overheating, corrosion, and non-compliant wiring that could trigger an overcurrent fault or arc flash event.

Insulation resistance and continuity testing

Using calibrated Megger test equipment, we measure insulation resistance across all branch circuits, feeder circuits, and service entrance conductors to catch deteriorated or damaged cable before it fails.

Ground fault and earth loop impedance verification

We test GFCI, RCD, and RCBO devices, verify grounding and bonding conductor integrity, and measure earth loop impedance to confirm your fault protection meets NEC and NFPA standards.

Thermographic infrared scanning

Our thermographic infrared scanning service identifies overloaded conductors, loose terminals, and defective contactors that standard visual inspection can’t detect. Where arc flash risk is a concern, our findings are documented in a format compatible with IEEE 1584 arc flash analysis, giving you a complete thermal and hazard picture of your electrical system.

Compliance documentation and inspection reports

Every inspection produces a detailed compliance report, test certificate, and defect notice where required, so you have a documented record for insurers, auditors, and regulatory bodies.

460+
Homes Serviced
92%
Same-Day Response
4+
Years of Experience
100%
Code-Compliant Work

Why Choose Our Commercial Property Electrical Inspection

Founded by Master Electrician David Koch (Indiana License #EC21400047) and serving Indiana commercial properties since 2008, Kochs Electric brings licensed, qualified electricians to every commercial property electrical inspection. We don’t send generalists. We carry general liability and workers’ compensation insurance on every engagement, and our inspection work follows NETA MTS (Maintenance Testing Specifications) standards where applicable. Every technician on our team is trained in NEC compliance, NFPA 70E arc flash safety, and OSHA electrical standards specific to commercial environments.

We carry full certification and licensing, and we work across a wide range of commercial property types — office buildings, retail spaces, warehouses, industrial facilities, and multi-tenant properties. Our inspection process covers everything from the utility connection and meter base through the main disconnect, sub-panels, distribution boards, and all branch circuits down to receptacles, outlets, and dedicated circuits for HVAC, emergency lighting, and fire alarm systems.

Our team uses professional-grade test equipment including Megger insulation resistance testers, power quality analyzers, and infrared scanning cameras. We don’t estimate or guess. We measure, verify, and document every finding with precision.

Kochs Electric delivers inspection reports that are clear, complete, and actionable. You’ll know exactly what’s compliant, what’s defective, and what remedial work is needed. We also offer follow-up repair and replacement services so you’re not left managing multiple contractors.

Trusted by commercial property owners and facility managers throughout Indiana, Kochs Electric is a licensed Indiana electrical contractor (License #EC21400047, verifiable at in.gov) built on accurate findings and actionable reports. Serving Indianapolis, Carmel, Fishers, and throughout Indiana – call (317) 680-7907 to schedule a commercial property electrical inspection.

Recent inspections include a 45,000 sq ft Indianapolis warehouse where thermographic scanning identified 14 overloaded branch circuits and two defective contactors in the distribution board – findings documented with NETA-format test data and delivered before the tenant move-in deadline; and a pre-purchase inspection on a 12,000 sq ft Carmel retail property that revealed a failing 400A main breaker and three ungrounded 240V circuits, giving the buyer documentation to negotiate a credit and a corrective action plan before closing.

 

commercial property electrical inspection square
commercial property electrical inspection wide

Ready to Get Started?

Contact our licensed team today for a clear, written quote with no surprises. We serve all of Indiana.

Call (317) 680-7907

Signs You Need Commercial Property Electrical Inspection

1

Tripping breakers or blown fuses on a regular basis:

Frequent overcurrent events on your MCB or MCCB panels point to an overloaded circuit, an undersized conductor, or a fault condition developing in your wiring. A commercial property electrical inspection identifies whether the load schedule matches the rated capacity of each circuit and whether breakers are correctly sized and functioning.

2

Visible damage, corrosion, or deterioration on wiring and panels:

Corroded terminals, damaged cable insulation, and deteriorated conduit are direct indicators of a system that needs professional assessment. Left uninspected, these defects escalate into short circuit events, ground faults, or arc flash incidents that put occupants and property at serious risk.

3

Unexplained increases in energy consumption:

A spike in kilowatt demand without a corresponding increase in operational load can signal leakage current, poor power factor, harmonic distortion, or a failing component drawing excess reactive power. Power quality analysis during a commercial electrical inspection pinpoints the source.

4

Preparing for a change of tenancy, sale, or renovation:

Commercial property transactions and major fit-outs require a verified electrical compliance report. Inspecting the service entrance, sub-panels, and all branch circuits before work begins confirms the existing system is safe to energize and capable of supporting new load demands.

5

Aging electrical infrastructure with no recent inspection record:

If your commercial property hasn’t had a documented electrical inspection in the past five years, the system may be non-compliant with current NEC requirements. Switchgear, transformers, and distribution boards degrade over time, and an inspection establishes a current baseline for maintenance and compliance planning.

Fully Licensed & Insured

State of Indiana

We Pull All Permits

You don’t lift a finger

NEC Code Compliant
Every project, every time
Workmanship Guarantee
We come back if anything fails

Our Commercial Property Electrical Inspection Process

1

Initial Assessment and Documentation Review

We start by reviewing any existing single line diagrams, load schedules, schematics, and previous inspection reports. This gives our electricians a clear picture of the system before we arrive on site.

2

Visual Inspection

Our team conducts a thorough visual inspection of all accessible electrical components — panels, switchgear, busbars, conduit, trunking, cable trays, junction boxes, terminals, receptacles, switches, and isolators. We flag exposed, damaged, or illegible labeled equipment immediately.

3

Instrument Testing

We run insulation resistance tests, continuity tests, polarity tests, earth loop impedance measurements, and GFCI/RCD functional tests across all circuits. Where required, we conduct high pot testing and load testing on critical circuits including HVAC, emergency lighting, and fire alarm circuits.

4

Thermographic Survey

Infrared scanning covers all panels, distribution boards, and high-load connection points to detect overheated conductors, loose connections, and defective components that aren’t visible to the eye.

5

Report and Certification

We compile a full inspection report, compliance report, and test certificate. Any defective or non-compliant items appear in a defect notice with clear remedial work recommendations. We walk you through every finding before we leave the site.

Brands We Use

Kochs Electric uses trusted, listed, and approved equipment and components during every commercial property electrical inspection and any associated repair or replacement work.

Fluke
Fluke
Megger
Megger
Flir
Flir
Eaton
Eaton
Square D
Square D
Siemens
Siemens
Leviton
Leviton
Hubbell
Hubbell
Klein Tools
Klein Tools
Fluke
Fluke
Megger
Megger
Flir
Flir
Eaton
Eaton
Square D
Square D
Siemens
Siemens
Leviton
Leviton
Hubbell
Hubbell
Klein Tools
Klein Tools

Using certified, approved components keeps your property safe and your inspection documentation clean.

Other Services

Commercial property electrical inspection

Commercial building electrical inspection

NEC compliance inspection commercial

Commercial electrical inspection services

Business electrical inspection

Insulation resistance testing commercial

Commercial property electrical compliance

Commercial electrical safety inspection

Earth loop impedance test commercial property

Commercial electrical panel inspection

Commercial switchgear inspection

Thermographic survey commercial electrical

Professional commercial electrical inspection

Licensed commercial electrical inspector

GFCI RCD testing commercial building

Commercial property electrical inspections

Annual commercial electrical inspection

Qualified electrician for commercial inspection

FAQs About Commercial Property Electrical Inspection

A commercial property electrical inspection is a structured assessment of all electrical systems in a commercial building. It covers the service entrance, main disconnect, sub-panels, distribution boards, branch circuits, wiring, grounding, bonding, and all connected devices. The goal is to verify that everything is safe, compliant, and functioning within rated parameters.

You should schedule an inspection before a property sale or purchase, before a major renovation or fit-out, after a significant electrical fault or fire, when changing tenants, or on a routine five-year cycle. Properties with aging infrastructure or no documented inspection history need one now.

Commercial electrical systems carry higher load demands, more complex distribution, and greater fault risk than residential systems. A qualified inspection identifies non-compliant wiring, overloaded circuits, defective breakers, and grounding failures before they cause equipment damage, fire, or injury.

Inspection time depends on the size and complexity of the property. A small retail space may take two to four hours. A large warehouse or multi-tenant building with multiple sub-panels and dedicated circuits can take a full day or more.

Yes. Kochs Electric offers repair, replacement, and remedial work services following any inspection. We can de-energize, isolate, replace, and re-energize defective components, and we’ll update your documentation to reflect the corrected system.

Every inspection Kochs Electric completes includes a full inspection report, test certificate, and defect notice where applicable. These documents support insurance requirements, regulatory compliance, and property transaction due diligence.

Same-Day Emergency Dispatch Available

Indiana's Trusted Residential Electricians

Licensed. Insured. NEC compliant. We pull permits and schedule inspections so you don’t have to. Call us today to get started.