Now Serving All of Indiana - Licensed electricians dispatched from Indianapolis.

Emergency calls welcome: (317) 680-7907

New Construction Electrical Inspection

Get your new construction wired right, inspected right, and approved the first time.

State Licensed
Master Electricians
Permit & Inspection Handled
24-Hour Emergency Line
Workmanship Guaranteed

Licensed, Bonded & Insured

NEC Code Compliant

Same-Day Emergency Response

Permits Pulled & Inspections Managed

Workmanship Guarantee

Serving All of Indiana

5 Highlights on New Construction Electrical Inspection

Rough-in inspection ready

Kochs Electric schedules and prepares every rough-in inspection before drywall goes up, verifying that all conduit runs, wire pulls, junction boxes, and panel rough-ins meet NEC code requirements.

Service entrance and meter base compliance

Our journeymen and master electricians install and inspect service entrances, meter bases, and main disconnects to satisfy utility company and local authority having jurisdiction (AHJ) standards.

AFCI and GFCI protection verified

Every branch circuit gets tested for arc-fault and ground-fault protection, confirming that tamper-resistant receptacles and GFCI devices are correctly installed in required locations.

Panel and load center inspection

We inspect load centers, subpanels, busbars, neutral bars, and ground bars for proper torque on lugs and terminals, correct wire sizing, and compliant labeling on every circuit breaker.

Permit card and final sign-off

Kochs Electric manages the inspection card from permit pull through final inspection, coordinating directly with the inspector to get your certificate of occupancy without delays.

460+
Homes Serviced
92%
Same-Day Response
4+
Years of Experience
100%
Code-Compliant Work

Why Choose Our New Construction Electrical Inspection

New construction electrical inspection is a multi-stage process. It demands precision at every phase, from rough-in through final inspection. Founded by Master Electrician David Koch (Indiana License #EC21400047) and serving Indiana builders since 2008, Kochs Electric brings licensed master electricians and experienced journeymen to homes, businesses, and job sites of every size. We carry general liability and workers’ compensation insurance on every project.

We wire, connect, and terminate to NEC 2023 standards as adopted in Indiana on every project. Our foremen verify that all conduit, Romex, MC cable, and EMT installations pass before the inspector ever walks the site. We also handle repairs and upgrades when needed to prevent compliance issues from slowing your project down.

As a licensed contractor, Kochs Electric holds all required state electrical licenses and carries full liability insurance. We’ve built a track record of passing rough-in inspections, safety inspections, and final inspections on the first visit across residential and commercial new construction projects.

Our team uses calibrated torque wrenches, voltage testers, and multimeters on every inspection walkthrough. We don’t guess at wire sizing or circuit load calculations. We provide accurate power load documentation, measure, verify, and certify before we call for inspection.

Builders and general contractors trust Kochs Electric because we communicate clearly, show up on schedule, and deliver compliant work. We coordinate with inspectors, pull permits, and keep your project moving. We schedule rough-in inspections within 48 hours of framing completion – call (317) 680-7907 any business day to set up a builder account or discuss your project. Serving Indianapolis, Carmel, Fishers, and throughout Indiana.

Recent projects include a 42-home residential subdivision in Fishers where we managed phased rough-in inspections across multiple active lots simultaneously, maintaining a first-pass rate and coordinating directly with the GC’s project manager via daily status updates; and a 28,000 sq ft commercial new construction in Indianapolis where we handled permit pull, rough-in, and final inspection sign-off within the GC’s original schedule, achieving certificate of occupancy without a single re-inspection.

 

new construction electrical inspection square
new construction electrical inspection wide

Ready to Get Started?

Contact our licensed team today for a clear, written quote with no surprises. We serve all of Indiana.

Call (317) 680-7907

Signs You Need New Construction Electrical Inspection

1

Rough-in work is complete but hasn't been verified:

Your electrician has run conduit, pulled wire, and mounted junction boxes throughout the framing. Before drywall gets installed, a new construction electrical inspection confirms that all rough-in work is compliant. Concealed wiring that fails inspection after drywall means costly tear-out. Catching non-compliant work at the rough-in stage saves time and money.

2

Your panel and subpanel installations haven't been checked:

A load center with improperly torqued lugs, overcrowded wiring, undersized feeders, or missing surge protection on dedicated equipment circuits is a fire hazard. New construction electrical inspection covers the panel, subpanel, busbar, neutral bar, and ground bar before the system gets energized. An inspector verifies that every circuit breaker is correctly sized and labeled.

3

AFCI and GFCI devices aren't confirmed compliant: 

NEC code requires arc-fault circuit interrupters on most branch circuits in new residential construction. Ground-fault protection is required in kitchens, bathrooms, near water sources, garages, and outdoor locations. If your electrician hasn’t verified AFCI and GFCI placement against current code, your final inspection will fail.

4

Service entrance and meter base work is complete:

The service entrance, meter base, and main disconnect are the first points of inspection for the utility company and the AHJ. Exposed conductors, improper bonding, or a non-compliant grounding electrode system will stop your project cold. New construction electrical inspection catches these issues before the utility energizes the service.

5

You're approaching final inspection without a pre-inspection walkthrough:

A failed final inspection delays your certificate of occupancy. Kochs Electric conducts a thorough pre-inspection walkthrough, testing every outlet, receptacle, switch, and fixture. We verify that all trim-out work is finished, all devices are properly secured, and the inspection card is complete before the inspector arrives.

Fully Licensed & Insured

State of Indiana

We Pull All Permits

You don’t lift a finger

NEC Code Compliant
Every project, every time
Workmanship Guarantee
We come back if anything fails

Our New Construction Electrical Inspection Process

1

Permit pull and plan review

Kochs Electric pulls the electrical permit and reviews the electrical plan and blueprints. We confirm that the planned circuit layout, panel sizing, and service entrance design comply with NEC code, city requirements, and local amendments.

2

Rough-in inspection preparation

Our journeymen walk the framing stage, verifying conduit runs, wire pulls, stapling, strapping, and junction box placement. We check that all boxes are accessible, correctly sized, and properly secured before we schedule the rough-in inspection.

3

Rough-in inspection coordination

We coordinate directly with the inspector, present the inspection card, and walk the site. Any items the inspector flags get corrected immediately. We re-schedule re-inspection without delay.

4

Trim-out and device installation

After drywall, our electricians install receptacles, outlets, switches, dimmers, lighting fixtures, and panels. We torque all lugs and terminals to spec, label every circuit breaker, and test each branch circuit with a voltage tester and multimeter.

5

Final inspection and sign-off

Kochs Electric schedules the final inspection and accompanies the inspector through the completed project. We verify that all AFCI, GFCI, and tamper-resistant devices pass, and we secure the final sign-off on the inspection card.

Brands We Use

Kochs Electric installs and inspects equipment from the most trusted names in the electrical industry. These brands meet NEC standards and pass inspection consistently.

Square D
Square D 
Leviton
Leviton
Eaton
Eaton
Hubbell
Hubbell 
Southwire
Southwire
Klein Tools
Klein Tools
Fluke
Fluke
Carlon
Carlon
Square D
Square D 
Leviton
Leviton
Eaton
Eaton
Hubbell
Hubbell 
Southwire
Southwire
Klein Tools
Klein Tools
Fluke
Fluke
Carlon
Carlon

Every brand Kochs Electric installs is UL listed and code compliant. We don’t cut corners on materials.

Other Services

New construction electrical inspection

New build electrical inspection

Rough-in inspection NEC compliance

Electrical inspection new construction

Residential new construction electrical

Panel inspection new construction

New construction electrical contractor

New home electrical inspection service

AFCI GFCI inspection new build

New construction wiring inspection

Commercial new construction electrical inspection

Service entrance inspection permit

Electrical permit inspection new construction

New construction electrical code inspection

Final electrical inspection certificate occupancy

FAQs About New Construction Electrical Inspection

A new construction electrical inspection is a code compliance review conducted by a licensed inspector at defined stages of a new build project. It covers rough-in wiring, panel installation, service entrance work, and final trim-out to confirm that all electrical work meets NEC standards and local code requirements.

Inspections happen at two primary stages. The rough-in inspection occurs after wiring, conduit, and junction boxes are installed but before drywall covers the work. The final inspection happens after all devices, fixtures, panels, and service equipment are fully installed and the system is ready to energize.

New construction electrical inspection protects occupants from fire hazards, shock risks, and non-compliant wiring. Safety is the primary reason electrical inspections exist at every stage. It also protects the property owner legally. Without a passed inspection and a signed inspection card, a building can’t receive a certificate of occupancy.

We pull permits, review blueprints, verify rough-in work against NEC code, torque all connections, test every circuit, and conduct a pre-inspection walkthrough before calling for inspection. Our goal is a first-time pass on every rough-in and final inspection.

Yes. Common reasons for failure include undersized wire, missing AFCI or GFCI protection, improperly torqued lugs, overcrowded panels, non-compliant grounding, and missing permits. Kochs Electric addresses all of these before the inspector arrives.

Yes. We pull the electrical permit, manage the inspection card, and coordinate scheduling with the local AHJ from start to final sign-off.

Same-Day Emergency Dispatch Available

Indiana's Trusted Residential Electricians

Licensed. Insured. NEC compliant. We pull permits and schedule inspections so you don’t have to. Call us today to get started.