Now Serving All of Indiana - Licensed electricians dispatched from Indianapolis.

Emergency calls welcome: (317) 680-7907

Variable Frequency Drive Installation

Professional VFD installation services that control motor speed, protect equipment, and cut energy costs across industrial and commercial applications. Kochs Electric handles the full scope of every variable frequency drive (VFD) project – from initial site assessment through programming, commissioning, and ongoing field service support.

State Licensed
Master Electricians
Permit & Inspection Handled
24-Hour Emergency Line
Workmanship Guaranteed

Licensed, Bonded & Insured

NEC Code Compliant

Same-Day Emergency Response

Permits Pulled & Inspections Managed

Workmanship Guarantee

Serving All of Indiana

5 Highlights on Variable Frequency Drive Installation

Precise motor speed control

VFD installation lets you dial in exact RPM and torque output for pumps, fans, compressors, and conveyors, replacing fixed-speed starters with fully adjustable drive systems

Reduced mechanical stress

Programmed ramp rates and controlled acceleration times eliminate hard starts, protecting motor bearings, shaft couplings, and connected gearboxes from shock loading

Energy savings on variable loads

 A properly commissioned VFD running a pump or fan at 80% speed draws roughly half the power of a full-speed contactor-started motor, cutting kilowatt-hour consumption measurably

Full parameter configuration

Kochs Electric programs carrier frequency, PWM settings, fault codes, overload thresholds, and 4-20mA or 0-10V control signals to match your exact motor nameplate and process requirements

Code-compliant wiring and grounding

Every installation includes shielded cable routing, proper ground bonding, conduit installation, and labeled terminal connections that meet NEC and NEMA enclosure ratings

460+
Homes Serviced
92%
Same-Day Response
4+
Years of Experience
100%
Code-Compliant Work

Why Choose Our Variable Frequency Drive Installation

Founded by Master Electrician David Koch (Indiana License #EC21400047) and serving Indiana industrial and commercial facilities since 2008, Kochs Electric brings qualified, hands-on expertise to every variable frequency drive installation. We carry general liability and workers’ compensation insurance on every job. Our electricians read motor nameplates, verify full load amps, check insulation class, and size the drive correctly before a single wire gets pulled. That upfront work prevents nuisance faults, overheating, and premature drive failure. Our experience across a wide range of industrial and commercial applications means we’ve seen every critical failure mode – and know how to prevent it before it reaches your floor.

We handle the complete scope. That means conduit routing, shielded cable installation, ground wire termination, control signal wiring, and full parameter programming in one visit. You don’t coordinate between a drive vendor and a separate electrical contractor. Kochs Electric does it all.

Our team commissions every VFD with a documented startup checklist. We verify input voltage, output frequency, motor current draw, and feedback signal accuracy before we hand the system over. If your process uses a PLC, HMI, or RS485 Modbus network, we configure the communication parameters and test the control loop end to end.

We stand behind our work with a clear service guarantee. If a fault develops related to our installation within the warranty period, we return and troubleshoot it at no additional charge. Our electricians carry calibrated clamp meters, megohmmeters, and oscilloscopes on every job. We don’t guess. We measure, verify, and confirm. For drive repair needs outside the warranty period, our field service team responds quickly – no need to send a failed unit to an outside repair shop when on-site diagnosis and component-level repair are available.

Kochs Electric serves industrial, commercial, and light manufacturing clients throughout Indianapolis, Carmel, Fishers, and Indiana. We work on three-phase and single-phase systems, low-voltage and medium-voltage applications, and new installations as well as drive replacements and upgrades. Call (317) 680-7907 to discuss your VFD project.

Recent installations include an ABB ACS880 VFD commissioned on a 75HP cooling tower fan at an Indianapolis manufacturing plant – post-installation metering confirmed a 44% reduction in kilowatt-hour consumption versus the prior fixed-speed contactor, recovering the installation cost in under eight months; and a Yaskawa V1000 replacement for a Carmel food processing pump application where the failed drive had no saved parameter data, with Kochs Electric reconstructing the full parameter set from the motor nameplate and process engineer notes, commissioning the replacement drive and returning the line to production in a single visit

variable frequency drive installation wide
variable frequency drive installation square

Ready to Get Started?

Contact our licensed team today for a clear, written quote with no surprises. We serve all of Indiana.

Call (317) 680-7907

Signs You Need Variable Frequency Drive Installation

1

Your motors are hard-starting and tripping breakers:

When a motor starts across the line through a contactor, inrush current can spike to six or eight times full load amps. That trips overcurrent protection, stresses the circuit breaker, and hammers the motor windings. A VFD controls the acceleration time and ramps current smoothly, eliminating nuisance trips on your panel or MCC.

2

Your pump or fan runs at full speed regardless of demand:

Fixed-speed operation on variable-load equipment wastes significant power. If your process only needs 60% flow half the time, running the motor at full RPM burns energy you’re paying for unnecessarily. Variable frequency drive installation lets you match motor speed to actual process demand through a setpoint signal or feedback loop.

3

You're getting excessive motor heat and bearing failures:

Unbalanced phase voltage, harmonic distortion from older starters, or continuous full-load operation without thermal relief shortens motor life. A properly filtered and programmed VFD regulates output voltage, reduces harmonic content, and protects the motor with built-in thermal overload monitoring.

4

Your process needs speed reversal or dynamic braking:

Conveyors, feeders, and hoists often require controlled deceleration or reverse direction. A VFD with a braking resistor and programmed deceleration time handles this cleanly. Contactors and soft starters can’t match that level of control.

5

You're replacing an old drive with no documentation:

Outdated drives lose parameter data when they fail. Kochs Electric pulls the motor nameplate data, re-engineers the parameter set, installs the replacement drive, and commissions the system with full documentation so the next service call takes minutes, not hours. We keep common VFDs in stock for fast-turnaround replacements.

Fully Licensed & Insured

State of Indiana

We Pull All Permits

You don’t lift a finger

NEC Code Compliant
Every project, every time
Workmanship Guarantee
We come back if anything fails

Our Variable Frequency Drive Installation Process

1

Site assessment and motor nameplate review

We inspect the existing panel, MCC, or switchgear, record input voltage, phase configuration, and available breaker capacity. We pull the motor nameplate data including horsepower, full load amps, insulation class, and service factor to size the drive correctly.

2

Drive selection and enclosure specification

We select a VFD matched to the motor’s rated current and the environment’s NEMA or IP rating requirements. Wash-down areas, dusty conveyor lines, and outdoor installations each need different enclosure protection.

3

Conduit routing and cable installation

We install conduit, pull shielded cable between the drive and motor, and route control wiring separately to prevent EMI and RFI interference on analog and digital signal lines.

4

Wiring, termination, and grounding

We terminate line-side and load-side conductors at the correct lug torque specs, connect the ground wire to the drive’s PE terminal, and bond the enclosure to the building ground system.

5

Parameter programming and configuration

We enter motor nameplate data, set acceleration and deceleration times, configure the control signal input (4-20mA, 0-10V, or network), and program fault response behavior.

6

Commissioning, testing, and handoff

We energize the drive, run the motor through its full speed range, verify output current and frequency with a clamp meter, confirm control signal response, and document all parameters for your records.

Brands We Use

Kochs Electric installs and programs variable frequency drives from proven, UL-listed manufacturers with strong service networks for parts and technical support.

ABB
ABB
Allen-Bradley
Allen-Bradley
Siemens
Siemens
Wago
Yaskawa
Danfoss 
Danfoss
Schneider Electric
Schneider Electric 
Eaton
Eaton
Mitsubishi Electric
Mitsubishi Electric
Bosch Rexroth 
Bosch Rexroth 
Teco-Westinghouse 
Teco-Westinghouse 
ABB
ABB
Allen-Bradley
Allen-Bradley
Siemens
Siemens
Wago
Yaskawa
Danfoss 
Danfoss
Schneider Electric
Schneider Electric 
Eaton
Eaton
Mitsubishi Electric
Mitsubishi Electric
Bosch Rexroth 
Bosch Rexroth 
Teco-Westinghouse 
Teco-Westinghouse 

Kochs Electric follows full lockout/tagout procedures on every installation and service call.

Other Services

Variable frequency drive installation

VFD installation service

Motor speed control wiring

Commercial VFD installation

Industrial drive installation

Three-phase motor drive setup

Variable frequency drive installer

Electric drive installation contractor

VFD parameter programming service

VFD replacement and upgrade

Drive commissioning service

Motor control center drive installation

Professional VFD wiring service

Adjustable frequency drive installation

VFD troubleshooting and configuration

FAQs About Variable Frequency Drive Installation

A variable frequency drive is an electronic device that controls AC motor speed by adjusting the output frequency and voltage delivered to the motor. It converts incoming AC power through a rectifier to DC, then inverts it back to AC at a controlled frequency using PWM switching. That process lets you run a motor at any speed between zero and its rated RPM. Variable frequency drives (VFDs) are also referred to as a frequency drive (VFD), adjustable speed drive, or inverter drive – all describing the same core technology.

Any application where the load varies — pumps, fans, compressors, conveyors — benefits from variable frequency drive installation. You also need a VFD when your process requires controlled acceleration, deceleration, or speed reversal that a contactor or soft starter can’t deliver.

A straightforward single-drive installation on an existing motor circuit typically takes four to eight hours. Larger projects involving MCC integration, PLC network configuration, or multiple drives run longer. Kochs Electric gives you a clear scope and timeline before work starts.

Most standard NEMA frame induction motors rated for inverter duty accept VFD control without modification. Older motors or those without inverter-duty insulation ratings may need evaluation. We check the motor nameplate and run a megohmmeter test before installation to confirm compatibility.

Yes. On variable torque loads like pumps and fans, reducing motor speed by 20% cuts power draw by roughly 50% due to the affinity laws governing fluid dynamics. The actual savings depend on your load profile, duty cycle, and current operating conditions.

Modern drives monitor overcurrent, overvoltage, undervoltage, ground fault, thermal overload, phase loss, and communication errors. Each condition generates a fault code on the display. Kochs Electric configures fault response behavior during commissioning so your system reacts appropriately to each condition.

Same-Day Emergency Dispatch Available

Indiana's Trusted Residential Electricians

Licensed. Insured. NEC compliant. We pull permits and schedule inspections so you don’t have to. Call us today to get started.