Now Serving All of Indiana - Licensed electricians dispatched from Indianapolis.

Emergency calls welcome: (317) 680-7907

USB Outlet Installation

Upgrade your modern home or office with professional USB outlet installation – no adapters, no clutter, just clean, built-in charging power where you need it.

State Licensed
Master Electricians
Permit & Inspection Handled
24-Hour Emergency Line
Workmanship Guaranteed

Licensed, Bonded & Insured

NEC Code Compliant

Same-Day Emergency Response

Permits Pulled & Inspections Managed

Workmanship Guarantee

Serving All of Indiana

5 Highlights on USB Outlet Installation

Built-in USB charging ports

USB outlet installation replaces standard receptacles with combo units that include built-in USB ports – USB-A or USB-C – directly in the wall plate, designed to charge smartphones, tablets, phones, and other devices without the need for bulky adapters, chargers, or power bricks.

Code-compliant wiring

Every installation follows NEC standards, with properly grounded, polarized, and amperage-rated receptacles connected to the correct circuit breaker in your panel.

Tamper-resistant and GFCI-protected options

Kochs Electric installs tamper-resistant, weather-resistant, and GFCI-protected USB outlets in kitchens, bathrooms, garages, and outdoor locations where code requires added protection.

Flush, recessed, or standard mounting

Outlets are mounted flush or recessed in a gang box or electrical box, secured with screws and anchors into drywall or stud framing for a clean, professional finish.

Fast, same-day service

Our licensed electricians wire, connect, and test each USB outlet on the same visit, confirming continuity, voltage, and proper ground fault protection before the job is done.

460+
Homes Serviced
92%
Same-Day Response
4+
Years of Experience
100%
Code-Compliant Work

Why Choose Our USB Outlet Installation

Founded by Master Electrician David Koch (Indiana License #EC21400047) and serving Indiana homes and businesses since 2008, Kochs Electric brings qualified, licensed electricians to every USB outlet installation job. We carry general liability and workers’ compensation insurance on every project. Our journeymen and master electricians handle load rating, box sizing, and correct wiring every time.

We don’t cut corners on materials. We use copper wire, quality NM cable (Romex), and rated wire connectors throughout. Every outlet gets secured in a code-compliant gang box or junction box, with the cover plate installed flush and tight.

Our team handles everything from a single USB outlet swap to a full home retrofit across multiple rooms. We pull permits where required, schedule inspections, and make sure the finish work meets both NEC requirements and your local inspector’s standards. Our electrical services cover all phases of the job, including permit coordination and final inspection sign-off.

Kochs Electric is trusted by homeowners and contractors throughout Indianapolis, Carmel, Fishers, and Indiana for reliable, professional USB outlet installation. Our licensed electricians stand behind every install with a workmanship guarantee.

Recent jobs include an Indianapolis homeowner’s home office where we installed four USB-C/A combination outlets on a dedicated 20A circuit, box depth verified for each backbox before installation and circuit loaded to 80% per NEC; and a Carmel short-term rental property where we replaced six standard outlets with Leviton USB-C combination outlets throughout the bedrooms and living areas, permits pulled and inspected before the next guest check-in.

usb outlet installation square
usb outlet installation wide

Ready to Get Started?

Contact our licensed team today for a clear, written quote with no surprises. We serve all of Indiana.

Call (317) 680-7907

Signs You Need USB Outlet Installation

1

You're using power adapters on every outlet:

If every standard receptacle in your home has a USB wall adapter plugged into it, you’re losing outlet space and creating unnecessary load on circuits shared by smartphones, tablets, phones, and other devices. A dedicated USB outlet installation frees up your standard receptacle slots and delivers charging current directly from the wall.

2

Your outlets are overloaded with charging cables:

Plugging multiple USB adapters into a single outlet or power strip can push a circuit toward its amperage limit, increasing the risk of surge damage. An electrician can install USB outlets on properly rated circuits with built-in surge protection, distributing the load across your panel without tripping breakers.

3

You're renovating a kitchen, bedroom, or home office:

Rough-in work during a renovation – whether the project involves plumbing, heating, or electrical upgrades – is the right time to run new NM cable, install a gang box, and wire in USB-C or USB-A combo receptacles. Doing it during finish work is cleaner and more cost-effective than retrofitting later.

4

Your current outlets are faulty or defective:

Cracked faceplates, loose receptacles, or outlets that fail a continuity test are signs of worn or defective hardware. Replacing them with new, amperage-rated USB outlets solves the problem and adds functionality at the same time.

5

You're adding a home theater, workshop, or charging station:

Dedicated spaces with high device counts need purpose-built charging solutions designed for high-volume use. Kochs Electric can wire and install multiple USB outlets on a single circuit, route cable through conduit, and label each circuit at the breaker box for easy identification.

Fully Licensed & Insured

State of Indiana

We Pull All Permits

You don’t lift a finger

NEC Code Compliant
Every project, every time
Workmanship Guarantee
We come back if anything fails

Our USB Outlet Installation Process

1

De-energize the circuit

Electrical safety comes first. We locate the correct breaker in your panel and trip it to cut power to the target outlet. We confirm the circuit is dead using a voltage tester and multimeter before touching any wiring.

2

Remove the existing outlet

We unscrew the cover plate and faceplate, pull the old receptacle from the electrical box, and disconnect the hot wire, neutral wire, and ground wire from their terminals.

3

Inspect the box and wiring

We check the gang box for damage, confirm the NM cable sheathing is intact, and inspect the copper wire for nicks or corrosion. If the box is too small for the new USB outlet, we replace it.

4

Wire and connect the USB outlet

We strip the wire ends, connect the hot wire to the brass terminal, the neutral wire to the silver terminal, and the ground wire to the green screw. We tighten each connection and secure the outlet in the box.

5

Test and finish

We re-energize the circuit, test voltage and continuity, confirm USB port output with a multimeter, and install the wall plate flush. The job is done when everything tests clean.

Brands We Use

Kochs Electric installs USB outlets from the most trusted names in the electrical industry. Quality hardware means reliable charging, longer service life, and code-compliant performance.

Leviton
Leviton
Hubbell
Hubbell
Legrand
Legrand
Pass & Seymour
Pass & Seymour
Eaton
Eaton
Lutron
Lutron
Southwire
Southwire
Klein Tools
Klein Tools
Square D
Square D
Leviton
Leviton
Hubbell
Hubbell
Legrand
Legrand
Pass & Seymour
Pass & Seymour
Eaton
Eaton
Lutron
Lutron
Southwire
Southwire
Klein Tools
Klein Tools
Square D
Square D

Every brand we use meets NEC standards. We never install unrated or defective hardware.

Other Services

USB outlet installation

USB receptacle installation

install USB wall outlet

USB outlet installer

USB charging outlet service

USB-C outlet wiring

USB outlet replacement

combo USB outlet install

USB outlet electrician

professional USB outlet installation

USB wall plate installation

GFCI USB outlet install

home USB outlet installation

USB outlet upgrade service

USB outlet NEC code compliant

FAQs About USB Outlet Installation

USB outlet installation is the process of replacing a standard electrical receptacle with a combo unit that includes one or more USB-A or USB-C charging ports built directly into the wall plate. An electrician disconnects the existing outlet, connects the new USB receptacle to the hot wire, neutral wire, and ground wire, and mounts it flush in the electrical box.

You need one when you’re tired of using adapters, when you’re renovating a room, or when you want dedicated charging ports in a kitchen, bedroom, home office, or garage. It’s also a smart upgrade during any electrical panel or circuit work. Contact us to schedule an appointment and our team will respond shortly to confirm your booking.

Wiring a USB outlet involves working with live circuits, connecting to a breaker box, and meeting NEC code requirements. Electrical safety is not something to cut corners on. A licensed electrician confirms the circuit is properly rated, the ground wire is connected, and the outlet tests clean before the job is closed out. Our professionals ensure every connection meets code before they leave the job site.

A single outlet swap takes 30 to 60 minutes, making it an efficient upgrade for most homeowners. Installing multiple USB outlets across several rooms can take two to four hours depending on the number of circuits involved and whether new NM cable needs to be run.

Yes. USB outlets can be installed in any room. Bathrooms, kitchens, and garages require GFCI-protected or tamper-resistant models per NEC code. Outdoor locations need weather-resistant rated receptacles.

In most jurisdictions, replacing a like-for-like outlet doesn’t require a permit. Running new circuits or adding outlets to a panel does. Kochs Electric handles permit applications and inspections when required.

Same-Day Emergency Dispatch Available

Indiana's Trusted Residential Electricians

Licensed. Insured. NEC compliant. We pull permits and schedule inspections so you don’t have to. Call us today to get started.